 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| COLOR MONITOR PN17LT/LO SERVICE COLOR MONITOR Manual CONTENTS 1. Precautions 2. Product Specifications 3. Disassembly & Reassembly 4. Alignment & Adjustments 5. Troubleshooting 6. Exploded View & Parts List PN17LT 7. Electrical Parts List 8. Block Diagram 9. Wiring Diagram 10. Schematic Diagrams PN17LO Samsung Electronics Co.,Ltd. 416, Maetan-3Dong, Paldal-Gu, Suwon City, Kyungki-Do, Korea. TEL : 1588-3366 Printed in Korea P/N : BH68-00393B-00 http://www.samsungmonitor.com (SyncMaster Worldwide) http://www.samsung-monitor.com (SyncMaster USA) http://www.samtron.com (SAMTRON Worldwide) http://www.sec.co.kr/monitor (Korea) 1 Precautions 1-1 Safety Precautions WARNINGS 1. For continued safety, do not attempt to modify the circuit board. 2. 3. Disconnect the AC power before servicing. When the chassis is operating, semiconductor heatsinks are potential shock hazards. 3. Leakage Current Hot Check (Figure 1-1): WARNING: Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test. (READING SHOULD NOT BE ABOVE 0.5mA) 1-1-1 Servicing the High Voltage and CRT : 4. WARNING:A high voltage adjusted to the wrong value may cause excessive X-ray emissions. 1. When servicing the high voltage system, remove the static charge by connecting a 10 kohm resistor in series with an insulated wire (such as a test probe) between the chassis and the anode lead. When troubleshooting a monitor with excessively HV, avoid being unnecessarily close to the monitor. Do not operate the monitor for longer than is necessary to locate the cause of excessive voltage. High voltage should always be kept at the rated value, no higher. Only when high voltage is excessive are X-rays capable of penetrating the shell of the CRT, including the lead in glass material. Operation at high voltages may also cause failure of the CRT or high voltage circuitry. When the HV regulator is operating properly, there is no possibility of an X-ray problem. Make sure the HV does not exceed its specified value and that it is regulating correctly. The CRT is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the CRT only with one that is the same or equivalent type as the original. Handle the CRT only when wearing shatterproof goggles and after completely discharging the high voltage anode. Do not lift the CRT by the neck. 2. 3. DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES LEAKAGE CURRENT TESTER 4. 2-WIRE CORD 5. ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED) EARTH GROUND Figure 1-1. Leakage Current Test Circuit 6. 1-1-3 Product Safety Notices Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by ! on schematics and parts lists. A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate. Components identified by on schematics and parts lists must be sealed by a soldering iron after replacement and adjustment. 7. 1-1-2 Fire and Shock Hazard : Before returning the monitor to the user, perform the following safety checks: 1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the monitor. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc. 2. PN17LT/LO 1-1 1 Precautions 1-2 Servicing Precautions WARNING1: First read the "Safety Precautions" section of this manual. If unforeseen circumstances create conflict between the servicing precautions and safety precautions, always follow the safety precautions. WARNING2: A high voltage adjusted to the wrong value may cause excessive X-ray emissions. WARNING3: An electrolytic capacitor installed with the wrong polarity might explode. 1. 2. Servicing precautions are printed on the cabinet, and should be followed closely. Always unplug the unit's AC power cord from the AC power source before attempting to: (a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect all test components in parallel with an electrolytic capacitor. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the area around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500 V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 6. 3. 7. Never defeat any of the +B voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last. 4. 8. 1-3 Electrostatically Sensitive Devices (ESD) Precautions Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some fieldeffect transistors. The following techniques will reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wriststrap device. To avoid a shock hazard, be sure to remove the wrist strap before applying power to the monitor. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of an electrostatic charge. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs. Use only a grounded-tip soldering iron to solder or desolder ESDs. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ESDs. 8. 6. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. Caution: Be sure no power is applied to the chassis or circuit and observe all other safety precautions. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD. Indicates ESDs on the Schematic Diagram in this manual. 7. 2. 3. 4. 5. 9. 1-2 PN17LT/LO 2 Product Specifications 2-1 Specifications Item Picture Tube: Description 17-Inch (43 cm): 16-inch (40.6 cm) viewable, Full-square flat-face tube, 90 Deflection, Semi- tint, Invar shadow mask, Anti-static silica coating, 0.26 mm Dot pitch Horizontal : 30 kHz ~ 70 kHz (Automatic) Unlimited colors Horizontal : 1280 Dots Vertical : 1024 Lines Vertical : 50 Hz ~ 160 Hz (Automatic) Scanning Frequency Display Colors Maximum Resolution Input Video Signal Input Sync Signal Maximum Pixel Clock rate Active Display Input Voltage Power Consumption Dimensions (W x D x H) (with base) Weight (Net/Gross) Environmental Considerations Analog, 0.7 Vp-p positive at 75 , internally terminated Separate Sync: TTL level positive/negative 110 MHz Horizontal : 312 mm 4 mm, AC 90 to 264 Volts, 60 Hz / 50 Hz 3 Hz 110 Watt (max) 15.66 x 16.22 x 15.75 Inches (398 x 412 x 400 mm) 33.1 lbs (15.0 kg) / 38.6 lbs (17.5 kg) Operating Temperature : 32F ~ 104F (0C ~ 40C) Humidity : 10 % ~ 80 % Storage Temperature : -4F ~ 113F (-20C ~ 45C) Humidity : 5 % ~ 95 % Vertical : 234 mm 4 mm * Above models comply with SWEDAC MPR II / TCO99 recommendations for reduced electromagnetic fields. * Designs and specifications are subject to change without prior notice. PN17LT/LO 2-1 2 Product Specifications 2-2 Pin Assignments Sync Type Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Red Green Blue N-C Separate Macintosh GND-R Red H/V Sync. Sense 0 Green GND-G Sense 1 Reserved Blue Sense 2 GND V-Sync. GND-B GND H-Sync. GND (DDC) GND-R GND-G GND-B Reserved (N-C) GND-Sync./Self-raster N-C DDC Data H-Sync. V-Sync. DDC Clock 1 6 7 2 8 12 3 9 13 14 10 5 15 Figure 2-1. Male Type Figure 2-2. Male Type 2-2 PN17LT/LO 2 Product Specifications 2-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1. Timing Chart Mode IBM VGA2/70 Hz VGA3/60 Hz 720 x 400 640 x 480 31.469 31.777 3.813 1.907 25.422 0.636 70.087 14.268 0.064 1.080 12.711 0.413 28.322 31.469 31.778 3.813 1.907 25.422 0.636 59.940 16.683 0.064 1.048 15.253 0.318 25.175 640/75 Hz 640 x 480 37.500 26.667 2.032 3.810 20.317 0.508 75.000 13.333 0.080 0.427 12.800 0.027 31.500 640/85 Hz 640 x 480 43.269 23.111 1.556 2.222 17.778 1.556 85.008 11.764 0.671 0.578 11.093 0.023 36.000 VESA 800/75 Hz 800 x 600 46.875 21.333 1.616 3.232 16.162 0.323 75.000 13.333 0.064 0.448 12.800 0.021 49.500 800/85 Hz 800 x 600 53.674 18.631 1.138 2.702 14.222 0.569 85.061 11.756 0.056 0.503 11.179 0.019 56.250 1024/75 Hz 1024 x 768 60.023 16.660 1.219 2.235 13.003 0.203 75.029 13.328 0.050 0.466 12.795 0.017 78.750 1024/85 Hz 1024 x 768 68.677 14.561 1.016 2.201 10.836 0.508 84.997 11.765 0.044 0.524 11.183 0.015 94.500 Timing fH (kHz) A sec B sec C sec D sec E sec fV (Hz) O msec P msec Q msec R msec S msec Clock Frequency (MHz) Polarity H.Sync V.Sync Remark Negative Positive Separate Negative Negative Separate Negative Negative Separate Negative Negative Separate Positive Positive Separate Positive Positive Separate Positive Positive Separate Positive Positive Separate Separate Sync Horizontal Video Video CC Vertical Video Video DD E E Q Q RR SS Sync Sync B B AA Sync Sync PP OO A : Line time total C : Back porch E : Front porch PN17LT/LO B : Horizontal sync width D : Active time O : Frame time total Q : Back porch S : Front porch P : Vertical sync width R : Active time 2-3 2 Product Specifications Memo 2-4 PN17LT/LO 3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the PN17LT/LO monitors. WARNING: This monitor contains electrostatically sensitive devices. Use with caution when handling these components. 3-1 Disassembly Cautions:1. Disconnect the monitor from the power source before disassembly. 2. To remove the Rear Cover, you must use the special opening jig tool. 3-1-1 Before making Disassembly 1. Disconnect or power cord from the monitor. 2. With a pad beneath it, stand the monitor on its front with the screen facing downward and the base close to you. 4. Push the Opening jig each groove along the top of the monitor till it makes a "ttak" sound. (2 grooves : Left and Right, Make sure each snap is disengaged.) 3-1-2 Cabinet Disassembly 1. Remove the Stand from the monitor. (Refer to Stand manual) 2. Remove 2 screws on the Rear cover. Figure 3 5. Pull the Rear Cover up off the monitor. Figure 1 3. Incline the monitor by lifting the rear of the monitor. Figure 4 6. Remove the Shield.(TCO 99) Figure 2 Figure 5 PN17LT/LO 3-1 3 Disassembly and Reassembly 7. Using pinch-nose pliers or ling-nose pliers, acrefully disconnect the Anode Cap from the CRT. Warning: Do not touch the Anode contact on the CRT (High Voltage may remain). 3-1-3 Removing the CRT Socket PCB 1. Complete all previous steps. 2. Lift up the Video Spring and remove the CRT Socket PCB from the CRT. Figure 7 6. Disconnect the Tilt connector at the CN304 connector on the Main PCB. 7. Disconnect the Sub PCB connector at the CN203 connector on the Main PCB. 8. Remove the screws on the back and along each side of the Bottom Chassis. 9. Carefully lift the Main PCB Ass'y and remove the remaining ground wires. 10. Place the Main PCB Ass'y on a flat, level surface that is protected from static electricity. Figure 6 3. Disconnect all connectors on the CRT Socket PCB. 4. Using a solder iron, disconnect Ground (GND) on the back of the Video Shield and remove the Shield Cap. 5. Remove the screw on the front of the Shield Socket. 6. Desolder the 4 tabs on the CRT Socket PCB and remove Shield. 7. Place the Video PCB on a flat, level surface that is protected from static electricity. 3-1-5 CRT Ass'y Disassembly 1. Complete all previous steps. 2. Straighten the Degaussing Coil Assembly coated metal ties and lift the Coil Ass'y from the CRT. 3. Remove the four corner screws and lift the CRT up and away from the Front Cover Assembly and place it on a padded surface. Caution: Do not lift the CRT by the neck. If you will be returning this CRT to the monitor, be sure to place the CRT face downward on a protective pad. 3-1-4 Removing the Main PCB 1. Complete all previous steps. 2. Disconnect the Degaussing Coil at GT601 and GT602 on the Main PCB. 3. Disconnect all easily accessible ground wires on the PCB and Bottom Chassis. 4. Disconnect the DY connector at the CN303 connector on the Main . 5. Using the jig, release the snaps (2) connecting the Front Cover and the PCB then lift up the Bottom to separate the two Shield. 3-2 Reassembly Reassembly procedures are in the reverse order of Disassembly procedures. 3-2 PN17LT/LO 4 Alignment and Adjustments This section of the service manual explains how to make permanent adjustments to the monitor. Directions are given for adjustments using the monitor Interface Board Ver. 2.0 and software (Softjig). 4-1 Adjustment Conditions Caution: Changes made without the Softjig are saved only to the user mode settings. As such, the settings are not permanently stored and may be inadvertently deleted by the user. 4-1-1 Before Making Adjustments 4-1-1 (a) ORIENTATION When servicing, always face the monitor to the east. 4-1-1 (b) MAGNETIC FIELDS Whenever possible, use magnetic field isolation equipment such as a Helmholtz field to surround the monitor. If a Helmholtz field is not available, frequently degauss the unit under test. Caution: Other electrical equipment may cause external magnetic fields which may interfere with monitor performance. Use an external degaussing coil to limit magnetic build up on the monitor. If an external degaussing coil is not available, use the internal degaussing circuit. However, do not use the internal degaussing circuit more than once per 30 minutes. 4-1-1 (c) WARM-UP TIME The monitor must be on for 30 minutes before starting alignment. Warm-up time is especially critical in color temperature and white balance adjustments. 4-1-1 (d) SIGNAL Analog, 0.7 Vp-p positive at 75 ohm, internal termination Sync: TTL level, negative/positive 4-1-1 (e) SCANNING FREQUENCY Horizontal: 30 kHz to 68 kHz (Automatic) Vertical: 50 Hz to 160 Hz (Automatic) Unless otherwise specified, adjust at the 1024 x 768 mode (68 kHz/85 Hz) signal. Refer to Table 2-1 on page 2-3. 4-1-2 Required Equipment The following equipment may be necessary for adjustment procedures: 4-1-2 (a) DISPLAY CONTROL ADJUSTMENT 1. Non-metallic (-) screwdriver: 1.5, 2.5, 3 mm 2. Non-metallic (+) screwdriver: 1.5, 2.5, 3 mm 3. Digital Multimeter (DMM), or Digital Voltmeter 4. Signal generator, or DM200 software 5. Software: Softjig or DM200 6. Interface Board Ver. 2.0 Code No. BH81-90001K 7. Parallel communications cable (25-pin to 25-pin); Code No. BH81-90001H 8. Signal cable (15-pin to 15-pin cable with additional 3-pin connector); Code No. BH81-90001J 9. 5 V DC adapter, not supplied 10. Personal computer Note: Softjig Ass'y (includes items 6, 7 and 9) Code No. BH81-90001L 4-1-2 (b) COLOR ADJUSTMENTS 1. All equipment listed in 4-1-2 (a), above 2. Color analyzer, or any luminance measurement equipment PN17LT/LO 4-1 4 Alignment and Adjustments 4-1-3 Connecting the SoftJig Connect the monitor to the signal generator and/ or PC as illustrated in Figures 4-1 and 4-2. Note: The signal cable connector which includes the 3-wire cable must connect to the monitor. If you use Setup 2 (PC only, no signal generator) you can only make adjustments to the signal timing available on that computer system. To make corrections to all factory timings requires the use of an additional signal generator. MONITOR INTERFACE BOARD VER. 2.0 5V DC ADAPTOR PARALLEL CABLE PC SIGNAL GENERATOR SIGNAL CABLE 3-WIRE CABLE Figure 4-1. Setup 1, With Signal Generator MONITOR INTERFACE BOARD VER. 2.0 5V DC ADAPTOR SIGNAL CABLE PARALLEL CABLE PC D-SUB CONNECTOR 3-WIRE CABLE Figure 4-2. Setup 2, Without Signal Generator 4-2 PN17LT/LO 4 Alignment and Adjustments 4-2 Display Control Adjustments 4-2-1 HIGH VOLTAGE ADJUSTMENT Signal: Display image: Contrast: Brightness: Limit: 1024 x 768 (68 kHz/85 Hz) Full White Pattern Maximum Maximum 26.0 kV 0.5 kV 4-2-3 CENTER RASTER Adjust SW401 so that the back raster comes to the center when you apply each basic mode. 4-2-4 Centering Centering means to position the center point of the display in the middle of the display area. Horizontal size and position and vertical size and position control the centering of the display. Adjust the horizontal size and vertical size to their optimal settings: 306 mm (H) x 230 mm. Adjust the horizontal position and vertical position to 4.0 mm of the center point of the screen. |A-B| 4.0 mm |C-D| 4.0 mm C DISPLAY AREA A B EDGE OF BEZEL D Expert) TSB CDT = 26.5kV 0.2 kV Measure the hight voltage level at the anode cap. High voltage should be within the limit as above. If the high voltage needs adjustment use the following procedure. PROCEDURE 1. Turn the power off and disconnect the AC line cord from the power source. 2. Turn the power on after connecting high voltage Probe. 3. Using the jig, adjust the high voltage to the specification. * High Voltage Adjustment PROCEDURE using Softjig x Select matching model name in "Model" field. Select " @7: Zero Beam" in menu after selecting "Extra 1" Adjust high voltage using control bar after selecting "HV MIN" Turn the power off/on after adjustment finished. Check the high voltage has been fixed with adjusted value after reselecting "@7: Zero Beam". Figure 4-3. Centering * In Softjig window, "Geometry" has to be selected for GD adjustment. 4-2-4 (a) HORIZONTAL SIZE ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum 4-2-2 SCREEN VOLTAGE CHECK CONDITIONS Signal: 1024 x 768 (68 kHz/85 Hz) Display image: Full White Pattern Contrast: Maximum Brightness: Maximum Limit: Refer to Table 4-1 No Adjustment. Only check with below table. Table 4-1 CRT type SDI TSB PHS M41QAQ261X011 M41LH507XX443 M41EJB523X170 Screen Voltage 500V 10V 630V 10V 570V 10V Use control bar after selecting "SIZE B+" in left menu to adjust the horizontal size of the display pattern to 306 mm with OSD "H-SIZE" fixed "39". (Tolerance: 3 mm.) Specially run "All mode save" after horizontal size adjustment in order to save "SIZE B+" values of other modes automatically. 4-2-4 (b) VERTICAL SIZE ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum Use control bar after selecting "V-SIZE" in left menu to adjust the vertical size of the display pattern to 234 mm. (Tolerance: 3 mm.) 4-3 PN17LT/LO 4 Alignment and Adjustments 4-2-4 (c) HORIZONTAL POSITION ADJUSTMENT CONDITIONS Scanning frequency: Display image: 68 kHz/85 Hz Crosshatch pattern 4-2-5 (a) HORIZONTAL LINEARITY ADJUSTMENT CONDITIONS Scanning frequency: 68 kHz/85 Hz Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum To adjust the Horizontal Linearity, refer to Table 4-2 for the tolerance range. Increase or decrease H_LIN to optimize the image. 4-2-5 (b) VERTICAL LINEARITY ADJUSTMENT CONDITIONS Scanning frequency: 68 kHz/85 Hz Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum To adjust the Vertical Linearity, refer to Table 4-2 for the tolerance range. Use control bar after selecting "V-LINEARITY BAL" in left menu to optimize the image. Use control bar after selecting "H-POSITION" in left menu to center the horizontal image on the raster. 4-2-4 (d) VERTICAL POSITION ADJUSTMENT CONDITIONS Scanning frequency: Display image: 68 kHz/85 Hz Crosshatch pattern Use control bar after selecting "V-POSITION" in left menu to center the vertical image on the raster. 4-2-5 Linearity X max-X min x100 X max+X min Y max-Y min Vertical Linearity = 2x x100 Y max+Y min Horizontal Linearity = 2x Table 4-2 Adjacent Linearity Entire Linearity Preset mode Pre-load mode (48kHz~) Pre-load mode (under 48kHz) 4% 5% 5% 8% 10% 14% Preset Mode : 68KHz / 85Hz Pre-load Mode : Refer to Timing Chart 4-4 PN17LT/LO 4 Alignment and Adjustments 4-2-6 Trapezoid Adjustment CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum 4-2-9 Side Pincushion Adjustment CONDITIONS Scanning frequency: Display image: 68 kHz/85 Hz Crosshatch pattern Use control bar after selecting "TRAPEZOID" in left menu to make the image area rectangular. | A - B | < 4 mm A A Use control bar after selecting "PINCUSHION" in left menu to straighten the sides of the image area. | C1 |, | C2 | 2.0 mm, | D1 |, | D2 | 2.0 mm. C2 D1 B B D2 Figure 4-4. Trapezoid C1 4-2-7 Pinbalance Adjustment CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum Figure 4-7. Pincushion 4-2-10 Tilt Adjustment CONDITIONS Scanning Frequency: Display image: Brightness: Contrast: D1 | D1 |, | D2 | 2.0 mm 68 kHz/85 Hz Crosshatch pattern Maximum Maximum D1 D2 Use control bar after selecting "ROTATION" in left menu to correct the tilt of the display. Figure 4-5. Pinbalance Use control bar after selecting "PINBALANCE" in left menu to optimize the image. 4-2-11 Degauss No adjustments are available for the degaussing circuit. The degaussing circuit can effectively function only once per 30 minutes. 4-2-8 Parallelogram Adjustment CONDITIONS Scanning Frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum 4-2-12 To Delete the User Mode Data To delete the adjustment data from the user modes, click "@4: USER DELETE" in right ment. 4-2-13 Save the Data To save the adjustment data for a mode, press "@3: ALL MODE SAVE" in right ment. Use control bar after selecting "PARALLEL" in left menu to make the image area rectangular. 4 mm Figure 4-6. Parallelogram PN17LT/LO 4-5 4 Alignment and Adjustments 4-3 Color Adjustments CAUTION: Check below condition before color adjustment Video signal : Analog 0.7 Vp-p (at 75 ) Sync : TTL level (H, V seperate signal) * Select "Color" in Softjig menu for color adjustment. 4-3-2 (b) R.G.B - GAIN ADJUSTMENT 1/3H-1/2H FRONT BEZEL OPENING 1/3V-1/2V BACK RASTER WHITE WINDOW 4-3-1 Color Coordinates (Temperature) Color temperature is a measurement of the radiant energy transmitted by a color. For computer monitors, the color temperature refers to the radiant energy transmitted by white. Color coordinates are the X and Y coordinates on the chromaticity diagram of wavelengths for the visible spectrum. CONDITIONS Measurement instrument: Color analyzer Scanning frequency: 68 kHz/85 Hz Display image: White flat field at center of display area Luminance: Maximum PROCEDURE Use the directions in sections 4-3-2 through 4-3-3 to adjust the color coordinates for: 9300K to x = 0.283 0.02, y = 0.298 0.02 6500K to x = 0.313 0.02, y = 0.329 0.02 Figure 4-8. White Box Pattern CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Green box pattern Cut-off Maximum 1. Click on the << or >> box next to R,G,B _GAIN to adjust the brightness of the Green Gain to 36 1 ft-L. 4-3-2 (c) WHITE BALANCE ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Full white pattern Cut-off Maximum FRONT BEZEL OPENING BACK RASTER 4-3-2 Color Adjustments for 9300K 4-3-2 (a) BACK RASTER COLOR ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: WHITE WINDOW Figure 4-9. Full White Pattern 68 kHz/85 Hz Back raster pattern Maximum Maximum 1. Click on the << or >> boxes next to R_GAIN and B_GAIN to make the video white. (For 9300K color adjustment: x = 0.283 0.02, y = 0.298 0.02.) Note: Do not touch the G_GAIN controls. 2. Check the ABL. If it is not within the specifications (30 1 ft-L), use the ABL controls to adjust it. 3. Select COLOR FACTORY SAVE to save the data. 4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION CONDITIONS Scanning frequency: 1. Select "@1: CHANNEL 1" in right menu to control the color for 9300K. 2. Adjust the luminance of the back raster to between 0.5 to 0.7 ft-L using contron bar after selecting "GREEN CUTOFF" in the menu. 3. Use control bar after selecting "BLUE CUTOFF" in left menu to set the "y" coordinate to 0.298 0.015 4. Use control bar after selecting "RED CUTOFF" in left menu to 0.283 0.015 * If color values would not be matched desirable values, repeat sequence 3 and 4 after readjusting "GREEN CUTOFF" control a little different. 68 kHz/85 Hz 4-6 PN17LT/LO 4 Alignment and Adjustments Display image: X-Y Coordinates: ABL Luminance Brightness: Contrast: Back raster pattern Full White Pattern x = 0.283 0.02, y = 0.298 0.02 Refer to 4-3-2(c) Maximum 5 ft-L, 24 ft-L 4-3-4 Focus Adjustment CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz (1024 x 768) "H" character pattern Cut off point Maximum 1. Check whether the color coordinates of the back raster satisfy the above spec. If they do not, return to 4-3-2 (a) and readjust all settings. 2. Display a full white pattern. 3. Select "Geometry" in softjig menu. 4. Select "@7: 5-ft " in right menu. 5. Check whether the white coordinates of the video meet the above coordinates spec. 6. Select "@8: 24-ft " in right menu. 7. Check whether the white coordinates of the video satisfies the above spec. If they do not, return to 4-3-2 (a) and readjust all settings. Select "Color" and click "@2: CHANNEL 2" for color ajdustment for 6500K Repeat the sequence of 9300K adjustment. The luminance values the same as 9300K, but the color coordinated of back raster and white box are : x = 0.313 0.015 y = 0.329 0.015 PROCEDURE 1. Adjust the Focus VR on the FBT to display the sharpest image possible. 2. Use Locktite to seal the Focus VR in position. 4-3-5 Color Purity Adjustment Color purity is the absence of undesired color. Conspicuous mislanding (unexpected color in a uniform field) within the display area shall not be visible at a distance of 50 cm from the CRT surface. CONDITIONS Orientation: Scanning frequency: Display image: Luminance: Monitor facing east 68 kHz/85 Hz) White flat field Cut off point at the center of the display area Note: Color purity adjustments should only be attempted by qualified personnel. PROCEDURE For trained and experienced service technicians only. Use the following procedure to correct minor color purity problems: 1. Make sure the display is not affected by external magnetic fields. 2. Make sure the spacing between the PCM assembly and the CRT stem is 29 mm 1 mm. 3. Display a green pattern over the entire display area. 4. Adjust the purity magnet rings on the PCM assembly to display a pure green pattern. (Optimum setting: x = 0.295 0.015, y = 0.594 0.015) Table 4-4. Color Purity Tolerances Red: Green: Blue: x = 0.640 0.015 x = 0.295 0.015 x = 0.142 0.015 y = 0.323 0.015 y = 0.594 0.015 y = 0.066 0.015 4-3-3 Luminance Uniformity Check Luminance is considered uniform only if the ratio of lowest to highest brightness areas on the screen is not less than 7.5:10. CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz (1024 x 768) White flat field Cut off point at 24 ft-L Maximum PROCEDURE Measure luminance at nine points on the display screen (see figure below). (For 9300K color adjustment: x = 0.283 0.02, y = 0.298 0.02) Figure 4-10. Luminance Uniformity Check Locations PN17LT/LO 5. When you have the PCMs properly adjusted, carefully glue them together to prevent their movement during shipping. 4-7 4 Alignment and Adjustments Memo 4-8 PN17LT/LO 5 Troubleshooting 5-1 Parts Level Troubleshooting Notes: Check the following circuits. * No raster appears: Power circuit, Horizontal output circuit. * High voltage develops but no raster appears: Video output circuits. * High voltage does not develop: Horizontal output circuits. 5-1-1 No Power Supply Check and replace D601 and FH1 WAVEFORMS 1 100 V (IC601, #1) Chirping noise exists? Yes Check and replace IC601. No Repeating start? Yes Check and replace D606. CH1 P-P = 100 V CH1 RMS = 350.2 V No 1 IC601 Pin 1 waveform is right? No Check and replace D614, IC601, Q602, and ZD601. Yes C622 Voltage is 13 V 0.5V? No Check and replace IC201, IC301, IC401, Q402, Q404, IC603, Q609, and Q611. Yes Operate normally? No Replace Main board. Yes Verify voltages. Done. PN17LT/LO 5-1 5 Troubleshooting 5-1-2 DPMS Failure Check signal source H/V Sync. video level. WAVEFORMS 2 100V (IC601, #1) Make No H/V Sync. (power off mode) CH1 P-P = 100V CH1 RMS = 325.8 V LED blinks? No Check IC201 Pin 40. Yes +12 V line off? No Check IC201 Pin 6. Yes 2 IC601 Pin 1 output voltage exists? Yes Done No Refer to 5-1-1 No Power Supply. 5-2 PN17LT/LO 5 Troubleshooting 5-1-3 H_Deflection Failure Does PWM output signal appear at Pin 6 (B_out) of IC401? Yes No Does DC 12V appear at Pin 10 of IC401? Yes No Check 12 V line. 3 WAVEFORMS Check IC401. 3 2.00 V (IC401, #6) 4 Does Horizontal pluse signal appear at Pin 8 of IC401? Yes No Check IC401. CH1 P-P = 2.00V CH1 RMS = 5.868V 4 1.00V (IC401, #8) 5 Does 20 Vp-p signal appear at Collector of Q403? No Check Q402, Q404 and T401. No Check Q403. CH1 P-P = 1.00V CH1 RMS = 1.298V 5 20.0 V (Q403, Collector) 7-1-4 S Correction Failure Check S1 ~ S4 signal. CH1 P-P = 20.0 V CH1 RMS = 46.80V S1~S4 signals are right at each frequency block? Yes Check and replace Q404, Q409, Q410, Q411, Q414, Q415, and Q416. No Check and replace IC201. PN17LT/LO 5-3 5 Troubleshooting 5-1-5 H_Lin. Failure IC201 Pin 21 voltage varies with different H_Lin. DAC values? Yes IC603 Pin 12 voltage varies with different H_Lin. DAC values? Yes Check Q412, Q413 and T402. No Check 13 V_1, Coil_5 V line. Check some parts around IC603. No Replace IC201. 5-1-6 Invariable H_Size IC401 Pin 6 voltage varies with different B_Out DAC values? Yes Q402 Gate output duty varies with different B_Out DAC values? No Check some parts around Q402, IC401 Pin 3 ~ 6. No Check and replace IC401. 5-1-7 Abnormal H_Size IC401 Pin 11 output duty varies with different B+ offset DAC values? Yes 6 No WAVEFORMS Check and replace IC201. 6 200 V (Q408, Collector) Q408 Collector waveform is right? Yes Check some parts around D409 and L401. No Check and replace Q405, Q406, Q407, and Q408. CH1 P-P = 200V CH1 RMS = 387.2V 5-4 PN17LT/LO 5 Troubleshooting 5-1-8 Side Pin or Trap Failure No WAVEFORMS Check and replace IC401. 7 1.00 V (IC401, #11) 7 IC401 Pin 11 output exists? Yes Refer to 5-1-7 Abnormal H_Size. CH1 P-P = 1.00V CH1 RMS = 3.008 V 5-1-9 Para. or Pin Balance Failure IC401 Pin 11 output varies with different DAC values? No Check some parts around IC401, Q405, Q406, Q407, Q408, and replace IC401. Yes Refer to 5-1-7 Abnormal H_Size. 5-1-10 Tilt Failure Check tilt connector connection IC201 Pin 20 output duty varies with different DAC values? Yes IC603 Pin 3 output varies with different DAC values? Yes Check and replace Q301 and Q302. No Check and replace IC201. No Check and replace IC603. PN17LT/LO 5-5 5 Troubleshooting 5-1-11 V Deflection Failure No WAVEFORMS Refer to 5-1-1 No Power Supply 8 500 V (IC401, #12) 13V and -10V lines are on? Yes 8 IC401 Pin 12 output exists? No Check and replace IC401. CH1 P-P = 500 V CH1 RMS = 1.425 V Yes 9 9 10.0 V (IC301, #6) IC301 Pin 6 output exists? No Check and replace some parts around IC301. Yes Check DY connector connection. CH1 P-P = 10.0 V CH1 RMS = 5.06 V 5-1-12 V Size or Position Variation Failure IC401 Pin 12 output varies with different DAC values? Yes Check and replace IC301. No Check and replace IC201 and IC401. 5-6 PN17LT/LO 5 Troubleshooting 5-1-13 High Voltage Failure WAVEFORMS 3 IC401 Pin 6 OSC pulse exists? No Check and replace IC401 and +12 V line. 3 2.00 V (IC401, #6) Yes 10 Q402 Gate driving pulse exists? No Check and replace Q401. CH1 P-P = 2.00 V CH1 RMS = 5.868 V 10 2.00 V (Q402, Gate) Yes 11 Q402 Drain pulse exists? No Check and replace Q403 and L402. CH1 P-P = 2.00 V CH1 RMS = 7.692V Yes Done 11 50.0 V (Q402, Drain) 5-1-14 ABL Failure CH1 P-P = 50.0 V CH1 RMS = 73.7V Input full white pattern to monitor. IC101 Pin 22 input exists and varies with different patterns? Yes Check CN102. Yes T501 Pin 8 output exists? No Check and replace IC101. No Check and replace T501. Yes IC201 Pin 26 output exists and varies with different patterns? Yes Done No Check and replace IC201. PN17LT/LO 5-7 5 Troubleshooting 5-1-15 Dynamic Focus Failure IC401 Pin 32 output is right? No WAVEFORMS Replace the IC401. 12 2.00 V (IC401, #32) 12 Yes Some parts around Q551 are right? No Replace failed part. CH1 P-P = 2.00V CH1 RMS = 6.124V Yes 13 13 50.0 V (T502, #6) T502 Pin 6 input is right? No Check and replace C432. Yes 14 CH1 P-P = 50.0V CH1 RMS = 75.6V T502 Pin 1 output is right? No 14 100 V (T502, #1) Replace the T502. No Check the connection between FBT Focus pin and CRT Socket PCB. CH1 P-P = 100V CH1 RMS = 124.0V 5-8 PN17LT/LO 5 Troubleshooting 5-1-16 No Video Check signal cable and connection. WAVEFORMS 15 1.00V (IC101 #5, 6, 7) 15 IC101 Pin 5, 6 and 7 inputs are right? Yes No Check the signal cable connection. CH1 P-P = 1.00V CH1 RMS = 2.452V 16 IC101 Pin 18, 19 and 20 outputs are right? Yes No 16 1.00V (IC101 #18,19,20) Check I2C bus and 12V line. 17 IC103 Pin 1, 2 and 3 outputs are right? Yes Cathode DC levels are right? No Check +12V, +72 V line. Check and replace IC103. CH1 P-P = 1.00V CH1 RMS = 2.792V 17 20.0V (IC103, #1, 2, 3) No Check +72V line. Check and replace IC102. CH1 P-P = 20.0V CH1 RMS = 40.52V Yes G2 voltage is right? No Check G2 wire, CRT Socket board and FBT. Yes Change CRT. Yes Done. PN17LT/LO 5-9 5 Troubleshooting 5-1-17 Micom Failure No WAVEFORMS Check IC608 and ZD603. 18 1.00 V (IC201, #13, 14) IC201 Pin 11 input voltage is 5V? Yes 18 IC201 Pin 13 and 14 inputs are right? Yes IC201 Pin 18 input is right? No Check C202, C203 and X201. CH1 P-P = 1.00 V CH1 RMS = 2.108V No Check Q608 and ZD602. Yes All in/output values are right? No Replace IC201. Yes Done 5-10 PN17LT/LO 5 Troubleshooting 5-1-18 OSD Failure Check CN104 and connector Ass'y. Yes 19 WAVEFORMS 19 1.00 V (IC104, #6) IC104 Pin 6 input is right? No Check CN102 Pin 14. Yes 20 CH1 P-P = 1.00V CH1 RMS = 4.516V IC104 Pin 8 input is right? No 20 1.00 V (IC104, #8) Check CN102 Pin 8. Yes IC104 Pin 7 and 8 inputs are right? No Check IC201 Pin 16 and 17. CH1 P-P = 1.00V CH1 RMS = 5.024V 21 1.00 V (IC101, #18,19,20) Yes IC104 Pin 12, 13 and 14 outputs are right? Yes 21 No Check and replace IC104. CH1 P-P = 1.00V CH1 RMS = 2.580V IC101 Pin 18, 19 and 20 outputs are right? Yes Check and replace IC103. No Check and replace IC101. Done PN17LT/LO 5-11 5 Troubleshooting 5-1-19 User Control Failure Does the DC level change at Pin 38 of IC201 when you push the button S/W? Yes Check IC201. No Check the button. (SW201 ~ SW204) 5-1-20 Degaussing Failure Check degaussing connector. RL601 operation is right? No Check D-coil and TH601. Yes Q601 base input is right? No Check and replace Q601. Yes IC201 Pin 4 output is right? No Check and replace IC201. Yes Done 5-12 PN17LT/LO 5 Troubleshooting 5-2 General Troubleshooting 5-2-1 No Picture No LED blinks? Refer to 5-2-2 Shut down. Yes LED is green color? No Check Micom. Yes Check G2 voltage, high voltage and R, G, B cathode voltage. 5-2-2 Shut Down Blinking LED's? No Check power supply. Yes Scan failure? Yes Check horizontal, vertical deflection system and check power supply secondary voltages. No Video failure? Yes Check Video board. No Check and replace IC201. Done PN17LT/LO 5-13 5 Troubleshooting 5-2-3 Missing Color WAVEFORMS Proper Video levels are on CN101 (D-Sub) Pin 1, 3 and 5? Yes 22 No Check signal generator. 22 10.0 V (R,G,B, Video) Proper Video signal is on all cathodes? Yes Proper DC voltage is on all cathodes? Yes G2 voltage is right? Yes Heater voltage is right? No Refer to 5-1-16 No Video. CH1 P-P = 10.0V CH1 RMS = 17.02V No Check IC101 Pin 14, 15 and 16. Check IC102. No Check D520. No Check D608, Q604 and T601. Yes G1 voltage is right? Yes Replace CRT. Yes Done No Check D504 and T501. 5-14 PN17LT/LO 5 Troubleshooting 5-2-4 Visible Retrace Check white balance adjustment. G2 voltage is right? No WAVEFORMS Check D520. 23 5.00V (Q502, Collector) Yes Blank pulse is on Pin 17 of IC401? No Check IC401. CH1 P-P = 5.00V CH1 RMS = 28.33V Yes 23 24 20.00V (CRT Socket, G1) V_FLB pulse is on Collector of Q502? Yes No Check Q502. CH1 P-P = 20.0V CH1 RMS = 66.68V 24 Does approve the Vertical pulse on the CRT Socket G1? Yes Done No Check CN102 and CN201. PN17LT/LO 5-15 5 Troubleshooting 5-2-5 Unsynchronized Image Check input signals Pin 2 and 3 of CN202. Signals are right? No Check Video Cable Yes Signals at Pin 30 and 31 of IC201 are right? Yes Signals at Pin 14 and 15 of IC401 are right? Yes Check circuits on Main board. No Check IC401 No Check IC201. Done 5-16 PN17LT/LO 5 Troubleshooting 5-2-6 Misconvergence Try readjusting convergence. The convergence is now within spec.? No Readjust convergence. Yes Done The convergence is now within spec.? No Change CRT and readjust convergence. Yes Done Done PN17LT/LO 5-17 5 Troubleshooting 5-2-7 Poor Focus Adjust focus VR of FBT. Improved focus? Yes Aging monitor and check for focus change. No Check focus leads from FBT to CRT Socket. Check the CRT Socket. Dynamic focus circuit is right? No Refer to 5-1-15 Dynamic Focus Failure. Yes Replace the CRT and verify focus. 5-2-8 Purity Failure Degaussing Purity is right? Yes Done No Degaussing circuit is right? No Refer to 5-1-20 Degaussing Failure. Yes Replace CRT and verify purity. 5-18 PN17LT/LO 7 Electrical Parts List 7-1 Main PCB Parts Loc. No. C409 C430 C432 C512 C601 C602 C608 CIS CIS CIS CIS CIS CIS CIS CIS CIS CIS CIS CIS CIS CIS CIS CIS CIS CN_DY CN101 CN102 CN201 CN202 CN203 CN501_G2 CN502 CN502_W CN601 D406 D409 D601 D608 D609 FBT+H/S FUSE HS301_CLAMP1 HS501_CLAMP1 HS501_CLAMP2 IC101 IC201 IC201_SOCK IC202 IC401 L401 L402 L403 L601 LJP1 LJP2 LJP3 LJP4 LJP5 LJP6 OP201 Q409 Code No. 2306-000248 2301-001125 2305-000310 2201-000020 2301-001195 2301-001195 2401-000863 3301-000233 BH68-00001A BH71-00108A BH72-00025A BH72-00026A BH72-00299A BH73-60304C BH75-00275A 6003-000103 BH71-00110A BH72-00297A BH75-00277A BH61-00002A BH71-00107A BH72-00024A BH73-00014A BH46-00002N 3711-003989 3711-004228 BH39-00280A 3711-003895 3711-003873 BH39-00288A BH39-00232A 3711-000024 BH39-00149A BH39-00326A 0402-001025 0402-001295 0402-000103 0402-001194 0402-000016 6003-000122 3601-000004 6502-000001 6502-000001 6502-000001 1201-001702 0903-001194 3704-001071 1103-001149 1204-001509 BH27-20345B BH27-00023A BH27-20342U BH27-00007A BH39-40306C BH39-40306C BH39-40306D BH39-40306D BH39-40305Z BH39-40306D 0601-001147 0505-001309 Description "C-FILM,MPPF" C-FILM,MPPF C-FILM,MPEF C-CERAMIC,DISC C-FILM,MPPF C-FILM,MPPF C-AL CORE-FERRITE LABEL/MARK-CDT SHIELD-VIDEO/CAP GUIDE-POWER SHAFT-POWER SHEET-LMF(LOW) RUBBER-SUPPORT UNIT-SHIELD/BOTTOM SCREW-TAPTITE SHIELD-BOTTOM SUPPORT-PCB UNIT-SHIELD/VIDEO SPRING-VIDEO SHIELD-VIDEO HOLDER-VIDEO HOLDER-RUBBER(NORMAL) MICOM-S/W,PN19LT CONNECTOR-HEADER CONNECTOR-HEADER CBF HARNESS CONNECTOR-HEADER CONNECTOR-HEADER CBF HARNESS CBF-HARNESS CONNECTOR-HEADER CBF-HARNESS W/HARNESS SOCKET-AC INLET DIODE-RECTIFIER DIODE-RECTIFIER DIODE-BRIDGE DIODE-RECTIFIER DIODE-RECTIFIER SCREW-TAPTITE FUSE-CARTRIDGE CABLE CLAMP CABLE CLAMP CABLE CLAMP IC-VIDEO AMP IC-MICROCONTROLLER SOCKET-IC IC-EEPROM IC-HOR./VER.PROCESSO COIL-CHOKE COIL-CHOKE COIL-CHOKE COIL-LINE FILTER CBF-HARNESS CBF-HARNESS CBF-HARNESS CBF-HARNESS CBF-HARNESS CBF-HARNESS LED FET-SILICON Specification 680nF,5%,250V,BK,26.5x16.5mm,2 600nF,5%,250V,TP,26x20x11.5,20 22nF,5%,250V,TP,14.5x8.8mm,7.5 10nF,10%,1kV,Y5P,BK,18x5,10 150nF,10%,275VAC,BK,26x16.5x7, 150nF,10%,275VAC,BK,26x16.5x7, 220uF,20%,400V,WT,BK,30x35,10 ZZ,18x9.5x28mm,-,ART-PAPER 100G,-,WHT,BLK,-,ALL,CDT PN15VT,SPTE,T0.2,-,-,CDA4507,ABS+PC,5V,IV16,-,CDA4507,ABS+PC,5V,IV16,-,PN17LT,AL+PC T0.35,-,-,-,-,-,DP15LT,CR V0,GRAY,-,14*7*10,-,PN17LT,-,SECC ,-,-,-,T1.0 BH,+,B,M2.6,L10,ZPC(YEL),SWRCH PN15VT,SECC ,T1.0,-,-,PN15VT,ABS VO,IV16,-,-,-,-,PN17LT,-,SPTE,-,-,-,T0.2 CDB7907,STS H14 ,T1.0,-,-,-,NORMAL CDT PN15VT,SPTE,T0.2,-,-,CDA4507,ABS+PC,5V,IV16,-,NORMAL CRT DEL,SILICON V2,GRAY,-,-,-,NORMAL PN19LT(PHOEINX),-,-,-,-,-,NOWALL,4P,1R,8mm,STRAIGHT,SN BOX,6P,1R,2MM,ANGLE,SN PN17L,UL1007,UL/CSA,13P/14P,350MM,BLU/WHT/RED,AWG26,SMH200-13,YBNH200-14,-,-,-,BOX,13P,1R,2mm,STRAIGHT,SN BOX,7P,1R,2mm,STRAIGHT,SN PN17LO,UL1007,UL/CSA,2P/2P,130MM,BLU/WHT,AWG26,YBNH200,SMP250,-,-,-,-,-,-,CBF-CO DP17MO,UL1032,UL/CSA,1P,290MM,RED,AWG22,YHF800-1,-,-,-,-,-,-,-,CBF-CONN ASS'Y BOX,3P,1R,2.5mm,STRAIGHT,SN 3P,150MM,BLK,UL1007,AWG22,SMH250-03 PN15H,UL1015,UL/CSA,5P,115mm,GREN/YELLOW,AWG18,ST780400-3,-,BK,AC250V/10A,35*14, ERD07-15,1.5KV,1.5A,-,TP GUR460L-5700,600V,4A,DO-201AD,BK D2SBA60,600V,1.5A,SIP-4,ST UG2D,200V,2A,DO-204AC,TP UF5404,400V,3A,DO-201AD,TP BH,+,B,M4,L12,ZPC(YEL),SWRCH18 250V,3.15A,SLOW-BLOW,CERAMIC,5x20mm DAWH-5NB,D15,L35,NTR,NYLON66 DAWH-5NB,D15,L35,NTR,NYLON66 DAWH-5NB,D15,L35,NTR,NYLON66 1267,DIP,24P,-,-,10dB,PLASTIC,5.25V,2.4W,0to+70C,-,-,-,-,-,ST 3P863,8Bit,SDIP,42P,600MIL,12MHz,ST,CMOS,PLASTIC,5V,-,-40to+85C,1040BYTE,48KBYTE 42P,DIP,SN,1.778mm 524C80D41,4KBit,DIP,8P,300MIL,10mS,5V,10%,PLASTIC,-25to+70C,10uA,CMOS,ST TDA4859,DIP,32P,400MIL,PLASTIC,16V,-,-20TO+70CC,ST,H/V DEF. PROCESSOR 120UH,+/-10%,DR1523(L-81,C:9.8),BK,-,-,8.2MH(250KHz),10%,DR8*11,-,-,-,-,10.5OHM,-,-,-,BULK 25MH MIN,-,SQE 2424,BULK,-,,60MM,BLK,1015,AWG22,-,-,-,-,,60MM,BLK,1015,AWG22,-,-,-,-,,80MM,BLK,1015,AWG22,-,-,-,-,,80MM,BLK,1015,AWG22,-,-,-,-,,160MM,BLK,1015,AWG22,-,-,-,-, ,80MM,BLK,1015,AWG22,-,-,-,-,ROUND,GRN,4.75mm,565nm IRF630,N,200V,10A,0.4OHM,100W,TO-220 Remarks SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA ! SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA PN17LT/LO 7-1 7 Electrical Parts List Loc. No. RL601 S/BTM+PCB SH/BTM+AC/SOCK SH/BTM+SH/LMF SH/BTM+VID/GND SH/VID SH/VID+H/S SH/VIDEO SH/VIDEO SH/VIDEO SIGNAL SK01 SW401 SW601 T401 T402 T501 T502 T601 T602 TH601 TH602 VIDEO_CLAMP_3 BD101 BD102 BD103 BD104 BD105 BD401 BD402 BD403 BD600 BD601 BD602 BD603 C101 C102 C103 C104 C107 C108 C109 C110 C114 C115 C116 C117 C118 C119 C120 C121 C122 C123 C124 C129 C201 C202 C203 C204 C205 C207 Code No. 3501-001111 6003-000010 6003-000010 6003-000010 6003-000010 6502-000001 6003-000010 BH39-00134A BH39-00150A BH39-00323A BH39-00282A 3704-001142 3406-000002 3403-001116 BH26-00027A BH26-00028A BH26-00109A BH26-00114A BH26-00100A BH26-30302S 1404-000002 1404-001020 6502-000127 3301-000011 3301-000011 3301-000011 3301-000011 3301-000011 3301-001450 3301-000011 3301-000011 3301-000011 3301-000011 3301-000011 3301-000011 2201-000285 2301-000148 2301-000148 2401-000025 2301-000014 2401-001334 2201-000119 2201-000119 2202-002009 2201-000119 2401-000025 2202-002009 2401-000292 2401-000393 2301-000148 2201-000285 2301-000010 2202-002009 2301-000148 2301-000148 2401-000025 2201-000389 2201-000389 2401-000603 2401-000603 2401-002075 Description RELAY-POWER SCREW-TAPTITE SCREW-TAPTITE SCREW-TAPTITE SCREW-TAPTITE CABLE CLAMP SCREW-TAPTITE CBF-HARNESS CBF-HARNESS CBF HARNESS CBF SIGNAL SOCKET-CRT SWITCH-ROTARY SWITCH-PUSH TRANS-HOR.DRIVE TRANS-H.LINEARITY TRANS FBT TRANS-FOUCS TRANS POWER-(S/W),LAYER TYPE TRANS-SYNC. THERMISTOR-PTC THERMISTOR-NTC CABLE CLAMP CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD C-CERAMIC,DISC C-FILM,PEF C-FILM,PEF C-AL C-FILM,PEF C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,MLC-AXIAL C-CERAMIC,DISC C-AL C-CERAMIC,MLC-AXIAL C-AL C-AL C-FILM,PEF C-CERAMIC,DISC C-FILM,PEF C-CERAMIC,MLC-AXIAL C-FILM,PEF C-FILM,PEF C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-AL C-AL Specification 12Vdc,250mW,5A,1FormA,15mS,5mS BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 DAWH-5NB,D15,L35,NTR,NYLON66 BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 -,200MM,BLK,UL1015,AWG18,35068-9822/35750-101 -,150MM,-,-,8*0.16TA*16,35750-1010 PN15LT,8*0.16TA*16,-,-,120MM,-,-,35068-9822,ST710095-3,-,-,-,-,-,-,PN17LO,15P/06P.07P,20276,1500MM,UL20276,IVORY,D-SUB/MALE,-,-,10P,22.5PI,25.6PI,NI,36Vdc,200mA,SP3T,30VDC,0.1A,2C2P,SELF LOCK,35.0MH,-,EI 1916,PL-3,-,310UH,5.2UH,6P,DR1425(C:5.0),YL-81,5.2UH/68.0MH,-,HL-1425E LC-13,CF1781,PN17L,1.12mH,HV45,FUR3556,375.0mohm,71.0Vdc,14P,-10 ~60,BK,27.0KV EE-1916,PN17L,5P,1.7mH,-,-,70mH,-,-,0.85ohm/8.5ohm,-,PL3,DMR30,EE-1916,20uH MAX, ER-3541(16P),PN15VO,390uH/82.0uH/37.5uH,16P(ER-3541),-,-,-,-,-,-,PL3,DMR30,J2A-1 3-1(250UH),-,-,SB-5S,UU1116,39ohm,20%,-,-,TR,RECT,8ohm,15%,-,17mW/C,BK DAWH-18NB,ID15,-,NTR,NYLON66 AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G AA,45ohm,35x0.6x57mm,50mA,TP,SN-20(ui2000),AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G 1nF,10%,1kV,Y5P,TP,8x5,5 10nF,5%,100V,TP,7x3.2x7mm,5mm 10nF,5%,100V,TP,7x3.2x7mm,5mm 100uF,20%,16V,GP,TP,6.3x11,5 6.8nF,5%,100V,TP,5.8x12.5mm,5m 470nF,20%,50V,GP,TP,5x11,2.5 100nF,+80-20%,50V,Y5V,TP,8x3,5 100nF,+80-20%,50V,Y5V,TP,8x3,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 100nF,+80-20%,50V,Y5V,TP,8x3,5 100uF,20%,16V,GP,TP,6.3x11,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 100uF,20%,16V,WT,TP,8x11.5mm,5 10uF,20%,100V,WT,TP,8x11.5,5 10nF,5%,100V,TP,7x3.2x7mm,5mm 1nF,10%,1kV,Y5P,TP,8x5,5 100nF,5%,100V,TP,11.5x12.5mm,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 10nF,5%,100V,TP,7x3.2x7mm,5mm 10nF,5%,100V,TP,7x3.2x7mm,5mm 100uF,20%,16V,GP,TP,6.3x11,5 0.022nF,5%,50V,NP0,TP,5x3,5 0.022nF,5%,50V,NP0,TP,5x3,5 1uF,20%,50V,GP,TP,5x11,5 1uF,20%,50V,GP,TP,5x11,5 4.7uF,20%,50V,GP,TP,5x11,5 Remarks SNA SNA SNA SNA SNA SNA ! ! SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA 7-2 PN17LT/LO 7 Electrical Parts List Loc. No. C209 C210 C211 C212 C213 C214 C215 C218 C301 C302 C305 C306 C307 C308 C309 C312 C401 C402 C403 C404 C405 C406 C407 C408 C410 C411 C412 C413 C414 C415 C416 C417 C419 C420 C421 C423 C425 C426 C427 C429 C431 C433 C434 C436 C437 C439 C500 C501 C502 C503 C504 C505 C508 C509 C510 C513 C551 C552 C553 C596 C597 Code No. 2401-002075 2401-000661 2201-000146 2201-000017 2301-000010 2401-000025 2201-000146 2301-000148 2305-000665 2305-000280 2401-001378 2401-002274 2305-000237 2301-000013 2202-002008 2401-000050 2301-000312 2201-000119 2305-000178 2301-000312 2201-000823 2301-000519 2401-000540 2201-000469 2401-000025 2301-000174 2301-000004 2401-001012 2401-001334 2401-001222 2301-000010 2301-000148 2301-001306 2309-000106 2303-000331 2401-000613 2306-000125 2401-000613 2306-000137 2401-000613 2306-000169 2305-001003 2401-000050 2201-000469 2401-000025 2202-002008 2401-000603 2301-000016 2301-000016 2401-000050 2301-000004 2401-000059 2401-002267 2401-000043 2301-000294 2201-000291 2401-000050 2201-000132 2201-000291 2201-000291 2201-000291 Description C-AL C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-FILM,PEF C-AL C-CERAMIC,DISC C-FILM,PEF C-FILM,MPEF C-FILM,MPEF C-AL C-AL C-FILM,MPEF C-FILM,PEF C-CERAMIC,MLC-AXIAL C-AL C-FILM,PEF C-CERAMIC,DISC C-FILM,MPEF C-FILM,PEF C-CERAMIC,DISC C-FILM,PEF C-AL C-CERAMIC,DISC C-AL C-FILM,PEF C-FILM,PEF C-AL C-AL C-AL C-FILM,PEF C-FILM,PEF C-FILM,PPF C-FILM,MPE-PPF C-FILM,PPF C-AL C-FILM,MPPF C-AL C-FILM,MPPF C-AL C-FILM,MPPF C-FILM,MPEF C-AL C-CERAMIC,DISC C-AL C-CERAMIC,MLC-AXIAL C-AL C-FILM,PEF C-FILM,PEF C-AL C-FILM,PEF C-AL C-AL C-AL C-FILM,PEF C-CERAMIC,DISC C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC Specification 4.7uF,20%,50V,GP,TP,5x11,5 2.2uF,20%,50V,GP,TP,5x11,5 0.1nF,5%,50V,SL,TP,5x3.5,5 1nF,10%,50V,Y5P,TP,5x3.5,5 100nF,5%,100V,TP,11.5x12.5mm,5 100uF,20%,16V,GP,TP,6.3x11,5 0.1nF,5%,50V,SL,TP,5x3.5,5 10nF,5%,100V,TP,7x3.2x7mm,5mm 100nF,5%,63V,TP,7.5x4.0x5.0mm, 220nF,10%,63V,TP,7.5x13.5mm,5m 470uF,20%,16V,WT,TP,10x20,5 220uF,20%,35V,WT,TP,10x12.5,5 1uF,5%,63V,TP,7.5x15.5mm,5mm 4.7nF,5%,100V,TP,10.5x12.5x6.5 10nF,+80-20%,50V,Y5V,TP,2.3X3. 10uF,20%,16V,GP,TP,5x11,2.5 8.2nF,5%,100V,TP,6x12.5mm,5mm 100nF,+80-20%,50V,Y5V,TP,8x3,5 10nF,5%,100V,TP,-,5mm 8.2nF,5%,100V,TP,6x12.5mm,5mm 0.27nF,5%,50V,SL,TP,8x3.5,5 3.3nF,5%,100V,TP,5.8x3x12.5,5m 150uF,20%,63V,LZ,TP,10x25,5 0.33nF,10%,500V,Y5P,TP,5.5x3,5 100uF,20%,16V,GP,TP,6.3x11,5 15nF,5%,100V,TP,7.2x4.0x7.5mm, 2.2nF,5%,100V,TP,5.5X10X2.9,5m 3.3UF,20%,50V,BP,TP,16X25,7.5 470nF,20%,50V,GP,TP,5x11,2.5 4.7UF,20%,160V,WT,TP,8X11.5MM,5 100nF,5%,100V,TP,11.5x12.5mm,5 10nF,5%,100V,TP,7x3.2x7mm,5mm 2.5NF,3%,1.6KV,TP,21.5X15.5X8.5MM,7.5 2.2nF,5%,1.6KV,TP,23x16x9,7.5m 4.7nF,5%,630V,TP,19.5x12x7,7.5 1uF,20%,50V,WT,TP,5x11,5 120nF,5%,250V,TP,19x15x7,7.5mm 1uF,20%,50V,WT,TP,5x11,5 180nF,5%,250V,TP,19x16.5x8,7.5 1uF,20%,50V,WT,TP,5x11,5 250nF,5%,250V,TP,19x18x9.5,7.5 10nF,5%,250V,TP,13x4.5x9mm,7.5 10uF,20%,16V,GP,TP,5x11,2.5 0.33nF,10%,500V,Y5P,TP,5.5x3,5 100uF,20%,16V,GP,TP,6.3x11,5 10nF,+80-20%,50V,Y5V,TP,2.3X3. 1uF,20%,50V,GP,TP,5x11,5 22nF,5%,100V,TP,7.2x4.5x9.0mm, 22nF,5%,100V,TP,7.2x4.5x9.0mm, 10uF,20%,16V,GP,TP,5x11,2.5 2.2nF,5%,100V,TP,5.5X10X2.9,5m 220nF,20%,50V,GP,-,5x11,5 2.2uF,20%,250V,GP,TP,8x11.5,5 1uF,20%,160V,GP,TP,6.3x11,5 56nF,5%,100V,TP,9.5x12.5mm,5mm 1nF,10%,500V,Y5P,TP,7.5x3.5,5 10uF,20%,16V,GP,TP,5x11,2.5 0.1nF,10%,500V,Y5P,TP,6.5x3,5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 Remarks ! ! SNA PN17LT/LO 7-3 7 Electrical Parts List Loc. No. C598 C599 C600 C603 C604 C607 C609 C610 C611 C612 C613 C614 C615 C616 C617 C618 C619 C620 C621 C622 C623 C626 C627 C628 C629 C630 C697 C698 C699 CB01 CB02 CB03 CB04 CG01 CG02 CG03 CG04 CN304 CN501 CN603 CR01 CR02 CR03 CR04 D301 D400 D401 D402 D403 D404 D405 D407 D410 D411 D412 D413 D420 D421 D501 D503 D504 Code No. 2201-000291 2201-000291 2201-002026 2201-000024 2201-000024 2202-002009 2401-000971 2301-000284 2401-000613 2401-000613 2201-000012 2201-000019 2201-000291 2201-000023 2201-000023 2401-000039 2201-000469 2401-000540 2401-001551 2401-000151 2401-000039 2401-000025 2401-000292 2401-000050 2401-000292 2401-000971 2201-000017 2201-000019 2202-002009 2202-002009 2301-000010 2201-000119 2305-000004 2202-002009 2301-000010 2201-000119 2305-000004 3711-000197 6042-000001 3711-000217 2202-002009 2301-000010 2201-000119 2305-000004 0402-000274 0401-000005 0402-000274 0402-000006 0402-000006 0402-000006 0402-000274 0402-000274 0402-000546 0402-000546 0402-000546 0402-000546 0401-000005 0401-000004 0401-000005 0402-000546 0402-000546 Description C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,MLC-AXIAL C-AL C-FILM,PEF C-AL C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-CERAMIC,DISC C-AL C-AL C-AL C-AL C-AL C-AL C-AL C-AL C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,MLC-AXIAL C-CERAMIC,MLC-AXIAL C-FILM,PEF C-CERAMIC,DISC C-FILM,MPEF C-CERAMIC,MLC-AXIAL C-FILM,PEF C-CERAMIC,DISC C-FILM,MPEF CONNECTOR-HEADER EYELET CONNECTOR-HEADER C-CERAMIC,MLC-AXIAL C-FILM,PEF C-CERAMIC,DISC C-FILM,MPEF DIODE-RECTIFIER DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER Specification 1nF,10%,500V,Y5P,TP,7.5x3.5,5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 1nF,20%,400VAC,B,TP,11x6,7.5mm 4.7nF,20%,250VAC,Y5U,TP,16x7,7 4.7nF,20%,250VAC,Y5U,TP,16x7,7 100nF,+80-20%,50V,Y5V,TP,2.3X3 22uF,20%,50V,WT,TP,6x11mm,5mm 47nF,5%,100V,TP,8.5x12.5mm,5mm 1uF,20%,50V,WT,TP,5x11,5 1uF,20%,50V,WT,TP,5x11,5 0.22nF,10%,1kV,Y5P,TP,6.3x5,5 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 2.2nF,20%,125V,Y5U,TP,11x7,5 2.2nF,20%,125V,Y5U,TP,11x7,5 1000uF,20%,16V,GP,TP,10x16,5 0.33nF,10%,500V,Y5P,TP,5.5x3,5 150uF,20%,63V,LZ,TP,10x25,5 47uF,20%,35V,GP,TP,6.3x11,5 1000uF,20%,25V,GP,TP,10x20,5 1000uF,20%,16V,GP,TP,10x16,5 100uF,20%,16V,GP,TP,6.3x11,5 100uF,20%,16V,WT,TP,8x11.5mm,5 10uF,20%,16V,GP,TP,5x11,2.5 100uF,20%,16V,WT,TP,8x11.5mm,5 22uF,20%,50V,WT,TP,6x11mm,5mm 1nF,10%,50V,Y5P,TP,5x3.5,5 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 100nF,+80-20%,50V,Y5V,TP,2.3X3 100nF,5%,100V,TP,11.5x12.5mm,5 100nF,+80-20%,50V,Y5V,TP,8x3,5 220nF,10%,100V,TP,12.7x16,5mm 100nF,+80-20%,50V,Y5V,TP,2.3X3 100nF,5%,100V,TP,11.5x12.5mm,5 100nF,+80-20%,50V,Y5V,TP,8x3,5 220nF,10%,100V,TP,12.7x16,5mm 1WALL,3P,1R,2.5mm,STRAIGHT,SN ID2.2,OD2.7,L3.1,SN,BSS3-E/EH 1WALL,3P,1R,3.96mm,STRAIGHT,SN 100nF,+80-20%,50V,Y5V,TP,2.3X3 100nF,5%,100V,TP,11.5x12.5mm,5 100nF,+80-20%,50V,Y5V,TP,8x3,5 220nF,10%,100V,TP,12.7x16,5mm UF4004,400V,1A,DO-41,TP 1N4148,100V,200mA,DO-35,TP UF4004,400V,1A,DO-41,TP 1N4007GP,1000V,1A,DO-41,TP 1N4007GP,1000V,1A,DO-41,TP 1N4007GP,1000V,1A,DO-41,TP UF4004,400V,1A,DO-41,TP UF4004,400V,1A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP 1SS244,250V,625mA,DO-34,TP 1N4148,100V,200mA,DO-35,TP TVR10G,400V,1.0A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP Remarks SNA SNA SNA 7-4 PN17LT/LO 7 Electrical Parts List Loc. No. D507 D508 D509 D510 D511 D512 D520 D597 D598 D602 D604 D605 D606 D607 D610 D611 D612 D614 D615 D616 D618 DB01 DB02 DB03 DB04 DB05 DG01 DG02 DG03 DG04 DG05 DR01 DR02 DR03 DR04 DR05 EY1 EY2 EY3 EY301 EY302 EY4 EY401 EY444 EY445 EY499 EY501 EY502 EY503 EY504 EY505 EY506 EY507 EY508 EY601 EY602 EY603 EY604 EY605 EY606 EY607 Code No. 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0402-000012 0401-000005 0401-000005 0401-000005 0402-000012 0402-000012 0402-000546 0401-000005 0402-000012 0402-001194 0402-000546 0402-000546 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000004 0401-000004 0401-000005 0401-000005 0401-000005 0401-000004 0401-000004 0401-000005 0401-000005 0401-000005 0401-000004 0401-000004 0401-000005 6042-000002 6042-000001 6042-000001 6042-000001 6042-000001 6042-000002 6042-000002 6042-000002 6042-000002 6042-000002 6042-000001 6042-000001 6042-000001 6042-000002 6042-000002 6042-000002 6042-000002 6042-000002 6042-000001 6042-000001 6042-000001 6042-000001 6042-000001 6042-000001 6042-000002 Description DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET Specification 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP UF4007,1KV,1A,DO-41,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP UF4007,1KV,1A,DO-41,TP UF4007,1KV,1A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP UF4007,1KV,1A,DO-41,TP UG2D,200V,2A,DO-204AC,TP TVR10G,400V,1.0A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1SS244,250V,625mA,DO-34,TP 1SS244,250V,625mA,DO-34,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1SS244,250V,625mA,DO-34,TP 1SS244,250V,625mA,DO-34,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1SS244,250V,625mA,DO-34,TP 1SS244,250V,625mA,DO-34,TP 1N4148,100V,200mA,DO-35,TP ID1.5,OD2,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH Remarks SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA PN17LT/LO 7-5 7 Electrical Parts List Loc. No. EY608 EY609 EY610 EY699 FH1 G2 GND GT603 GT604 IC102 IC104 IC603 J1 J10 J14 J15 J2 J23 J24 J3 J4 J5 J6 J7 J78 J8 J9 JP_DDC1 JP_DDC2 JP_DHHS JP1 JP10 JP11 JP12 JP13 JP14 JP15 JP16 JP17 JP18 JP19 JP2 JP20 JP21 JP22 JP23 JP24 JP25 JP26 JP27 JP28 JP29 JP3 JP30 JP31 JP32 JP33 JP34 JP35 JP36 JP37 Code No. 6042-000002 6042-000002 6042-000002 6042-000002 3602-000001 BH71-40300A BH71-40300A BH71-40300A BH71-40300A BH13-00022A 1204-001767 1201-000229 BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U Description EYELET EYELET EYELET EYELET FUSE-CLIP PIN-HINGE PIN-HINGE PIN-HINGE PIN-HINGE IC-BIAS CLAMP IC-OSD PROCESSOR IC-OP AMP CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS Specification ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH -,-,30mohm -,BRASS,D2.36,SN,HEAT/SINK -,BRASS,D2.36,SN,HEAT/SINK -,BRASS,D2.36,SN,HEAT/SINK -,BRASS,D2.36,SN,HEAT/SINK LM2480NA,PN15H/17L,8P,0to+70C,DIP,3mA,85V,ST S5D2510X02-D0B0,DIP,16P,300MIL,PLASTIC,5.25V,1.2W,-20to+70C,ST,324,DIP,14P,300MIL,QUAD,100V/m 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. Remarks SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA 7-6 PN17LT/LO 7 Electrical Parts List Loc. No. JP38 JP39 JP4 JP40 JP41 JP42 JP43 JP44 JP45 JP46 JP47 JP48 JP49 JP5 JP50 JP51 JP52 JP53 JP54 JP55 JP56 JP57 JP58 JP59 JP6 JP60 JP61 JP62 JP63 JP64 JP65 JP66 JP67 JP68 JP69 JP7 JP70 JP71 JP72 JP73 JP74 JP75 JP76 JP77 JP79 JP8 JP80 JP81 JP83 JP9 L403 LB02 LG02 LR02 MP1.0 Q101 Q301 Q302 Q401 Q403 Q405 Code No. BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH27-20343H 2701-000319 2701-000319 2701-000319 BH41-00125A 0501-000404 0501-000122 0501-000581 0501-000122 0501-000372 0501-000303 Description CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS COIL-PEAKING INDUCTOR-AXIAL INDUCTOR-AXIAL INDUCTOR-AXIAL PCB MAIN TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL Specification 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 2.7MH,10%,DR8*8,TP,-,470nH,20%,3x7mm 470nH,20%,3x7mm 470nH,20%,3x7mm PN17L*,FR1,1,-,1.6T,247*247,-,-,-,KSD1616-Y,NPN,750mW,TO-92,TP,135-270 2N3904,NPN,625mW,TO-92,TP,100-300 2N3906,PNP,625mW,TO-92,TP,100-300 2N3904,NPN,625mW,TO-92,TP,100-300 KSC2383-Y,NPN,900000mW,TO-92L,TP,160-320 KSA733,PNP,250mW,TO-92,TP,120-240 Remarks SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA PN17LT/LO 7-7 7 Electrical Parts List Loc. No. Q406 Q407 Q412 Q413 Q414 Q415 Q416 Q501 Q502 Q551 Q601 Q602 Q604 Q608 Q609 Q610 Q611 Q612 Q614 Q615 R100 R101 R102 R104 R105 R106 R107 R108 R109 R110 R111 R114 R115 R116 R117 R118 R119 R120 R121 R125 R200 R201 R202 R203 R204 R206 R207 R208 R209 R210 R211 R212 R213 R214 R215 R216 R217 R218 R219 R220 Code No. 0501-000303 0501-000140 0501-000122 0501-000581 0501-000586 0501-000586 0501-000586 0501-000586 0501-000143 0501-000413 0501-000586 0501-000122 0501-000404 0501-000010 0501-002228 0501-000586 0501-002228 0501-000586 0501-000404 0501-000581 2001-000241 2001-001138 2001-000429 2001-000273 2001-000429 2001-000290 2001-000281 2001-000281 2001-000734 2001-000003 2001-000003 2001-000290 2001-000331 2001-000812 2001-000290 2001-000734 2001-000003 2001-000429 2001-001138 2001-000890 2001-000869 2001-000812 2001-000290 2001-000008 2001-000008 2001-000008 2001-000869 2001-000869 2001-000290 2001-000290 2001-000660 2004-000796 2001-000429 2001-000429 2001-000281 2001-000281 2001-000281 2001-000281 2001-000290 2001-000281 Description TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL R-CARBON R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON Specification KSA733,PNP,250mW,TO-92,TP,120-240 2N5551,NPN,625mW,TO-92,TP,80-250 2N3904,NPN,625mW,TO-92,TP,100-300 2N3906,PNP,625mW,TO-92,TP,100-300 KSC945,NPN,250mW,TO-92,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 2N6520,PNP,625mW,TO-92,TP,30-200 KSP44,NPN,625mW,TO-92,TP,50-200 KSC945,NPN,250mW,TO-92,TP,120-240 2N3904,NPN,625mW,TO-92,TP,100-300 KSD1616-Y,NPN,750mW,TO-92,TP,135-270 KSC1008,NPN,800mW,TO-92,TP,120-240 KTA1281,PNP,1000mW,TO-92L,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KTA1281,PNP,1000mW,TO-92L,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KSD1616-Y,NPN,750mW,TO-92,TP,135-270 2N3906,PNP,625mW,TO-92,TP,100-300 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM 390OHM,5%,1/2W,AA,TP,2.4X6.4MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,1/8W,AA,TP,1.8x3.2mm 330ohm,5%,1/8W,AA,TP,1.8x3.2mm 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,1/8W,AA,TP,1.8x3.2mm 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 390OHM,5%,1/2W,AA,TP,2.4X6.4MM 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM 33Kohm,1%,1/4W,AA,TP,2.4x6.4mm 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM Remarks ! ! 7-8 PN17LT/LO 7 Electrical Parts List Loc. No. R221 R222 R223 R224 R225 R229 R230 R236 R240 R299 R301 R302 R303 R304 R306 R307 R308 R309 R310 R311 R312 R315 R316 R323 R324 R402 R403 R404 R405 R406 R407 R408 R409 R410 R412 R413 R414 R415 R416 R417 R418 R419 R420 R422 R423 R424 R425 R426 R427 R428 R429 R430 R431 R432 R434 R435 R436 R437 R438 R439 R440 Code No. 2001-000734 2001-000734 2001-000005 2001-000869 2001-000869 2001-000281 2001-000290 2001-000290 2001-000221 2001-000034 2001-000869 2004-000580 2001-000890 2001-000890 2004-001022 2001-001053 2001-001088 2004-004014 2004-001136 2001-000890 2001-000812 2004-004014 2001-000281 2001-000290 2001-000878 2001-000869 2004-001226 2004-000498 2001-000591 2001-000522 2001-000109 2001-000429 2001-000812 2003-000650 2001-000290 2001-001038 2001-001038 2003-000432 2001-000107 2001-000290 2001-000221 2001-000397 2001-000354 2001-001006 2001-000258 2004-000216 2001-000044 2001-000110 2001-000429 2003-000653 2001-000319 2001-001078 2003-000407 2001-000020 2001-000449 2001-000786 2001-000449 2001-000786 2001-000449 2001-000786 2001-000290 Description R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-METAL R-CARBON(S) R-CARBON(S) R-METAL R-METAL R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-METAL R-CARBON R-CARBON R-CARBON(S) R-CARBON R-CARBON R-METAL OXIDE(S) R-CARBON R-CARBON(S) R-CARBON(S) R-METAL OXIDE(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-CARBON R-METAL OXIDE(S) R-CARBON R-CARBON(S) R-METAL OXIDE(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON Specification 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 390ohm,5%,1/8W,AA,TP,1.8x3.2mm 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 220OHM,5%,1/4W,AA,TP,2.4X6.4MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 22Kohm,1%,1/4W,AA,TP,2.4x6.4mm 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6Kohm,1%,1/4W,AA,TP,2.4x6.4m 1.5OHM,5%,1/2W,AA,TP,2.4X6.4MM 1KOHM,5%,1/2W,AA,TP,2.4X6.4MM 2.4ohm,1%,1/4W,AA,TP,2.4x6.4mm 6.8Kohm,1%,1/4W,AA,TP,2.4x6.4m 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.4ohm,1%,1/4W,AA,TP,2.4x6.4mm 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 750ohm,1%,1/4W,AA,TP,2.4x6.4mm 2.7Kohm,1%,1/4W,AA,TP,2.4x6.4m 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM 470OHM,5%,1/2W,AA,TP,2.4X6.4MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,2W,AA,TP,4x12mm 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 0.56OHM,5%,1/2W,AA,TP,2.4X6.4MM 0.56OHM,5%,1/2W,AA,TP,2.4X6.4MM 1.5Kohm,5%,3W,AA,TP,6x16mm 150KOHM,5%,1/2W,AA,TP,2.4X6.4MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 180KOHM,5%,1/8W,AA,TP,1.8X3.2MM 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM 82OHM,5%,1/8W,AA,TP,1.8X3.2MM 1.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10Kohm,1%,1/4W,AA,TP,2.4x6.4mm 1.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM 10OHM,5%,1/4W,AA,TP,2.4X6.4MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,3W,AA,TP,6x16mm 120KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/2W,AA,TP,2.4X6.4MM 0.6ohm,5%,2W,AA,TP,4x12mm 22OHM,5%,1/2W,AA,TP,2.4X6.4MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM Remarks ! ! ! PN17LT/LO 7-9 7 Electrical Parts List Loc. No. R441 R443 R444 R445 R446 R450 R451 R452 R453 R454 R455 R500 R501 R502 R504 R505 R506 R507 R508 R509 R510 R511 R513 R514 R516 R518 R521 R524 R525 R526 R527 R529 R531 R551 R552 R553 R554 R555 R556 R557 R598 R599 R600 R601 R602 R603 R604 R605 R606 R608 R609 R610 R611 R612 R614 R615 R617 R618 R619 R621 R622 Code No. 2001-000290 2003-000650 2003-000769 2001-000019 2001-000117 2001-000786 2001-000290 2001-000290 2001-000290 2003-000650 2001-000211 2001-000435 2001-000890 2004-000979 2001-000008 2001-000924 2004-000657 2004-000216 2001-001129 2001-001129 2001-000837 2001-000478 2004-001349 2001-001071 2001-001108 2001-001108 2001-001129 2001-000660 2001-000273 2001-000702 2001-000356 2001-000429 2001-000786 2001-000530 2001-000537 2001-001129 2001-000087 2001-000042 2001-000890 2001-000087 2001-000290 2001-000958 2001-001129 2001-001129 2001-000023 2001-000290 2001-000857 2001-000734 2003-000014 2001-000281 2002-001068 2002-001068 2001-000376 2003-000738 2001-001107 2001-001088 2001-001037 2001-000429 2003-000471 2001-000071 2001-000016 Description R-CARBON R-METAL OXIDE(S) R-METAL OXIDE(S) R-CARBON(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-METAL OXIDE(S) R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-METAL R-METAL R-CARBON(S) R-CARBON(S) R-CARBON R-CARBON R-METAL R-CARBON(S) R-CARBON(S) R-CARBON(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON(S) R-CARBON R-CARBON R-CARBON(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-METAL OXIDE(S) R-CARBON R-COMPOSITION R-COMPOSITION R-CARBON R-METAL OXIDE(S) R-CARBON(S) R-CARBON(S) R-CARBON(S) R-CARBON R-METAL OXIDE(S) R-CARBON R-CARBON(S) Specification 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,2W,AA,TP,4x12mm 680ohm,5%,3W,AA,TP,6x16mm 10OHM,5%,1/2W,AA,TP,2.4X6.4MM 68OHM,5%,1/2W,AA,TP,2.4X6.4MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,2W,AA,TP,4x12mm 1OHM,5%,1/4W,AA,TP,2.4X6.4MM 1MOHM,5%,1/8W,AA,TP,1.8X3.2MM 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47Kohm,1%,1/4W,AA,TP,2.4x6.4mm 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM 680OHM,5%,1/8W,AA,TP,1.8X3.2MM 27Kohm,1%,1/4W,AA,TP,2.4x6.4mm 10Kohm,1%,1/4W,AA,TP,2.4x6.4mm 330KOHM,5%,1/2W,AA,TP,2.4X6.4MM 330KOHM,5%,1/2W,AA,TP,2.4X6.4MM 51KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.7OHM,5%,1/4W,AA,TP,2.4X6.4MM 91Kohm,1%,1/4W,AA,TP,2.4x6.4mm 12KOHM,5%,1/2W,AA,TP,2.4X6.4MM 22KOHM,5%,1/2W,AA,TP,2.4X6.4MM 22KOHM,5%,1/2W,AA,TP,2.4X6.4MM 330KOHM,5%,1/2W,AA,TP,2.4X6.4MM 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM 39KOHM,5%,1/8W,AA,TP,1.8X3.2MM 150KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 240KOHM,5%,1/4W,AA,TP,2.4X6.4MM 24KOHM,5%,1/4W,AA,TP,2.4X6.4MM 330KOHM,5%,1/2W,AA,TP,2.4X6.4MM 120KOHM,5%,1/2W,AA,TP,2.4X6.4MM 1KOHM,5%,1/4W,AA,TP,2.4X6.4MM 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 120KOHM,5%,1/2W,AA,TP,2.4X6.4MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 750OHM,5%,1/8W,AA,TP,1.8X3.2MM 330KOHM,5%,1/2W,AA,TP,2.4X6.4MM 330KOHM,5%,1/2W,AA,TP,2.4X6.4MM 47OHM,5%,1/4W,AA,TP,2.4X6.4MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 560OHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10Kohm,5%,3W,AA,TP,6x16mm 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 180Kohm,5%,1/2W,AA,TP,3.9x9mm 180Kohm,5%,1/2W,AA,TP,3.9x9mm 15OHM,5%,1/8W,AA,TP,1.8X3.2MM 56Kohm,5%,2W,AA,TP,4x12mm 220ohm,5%,1/2W,AA,TP,2.4x6.4mm 1KOHM,5%,1/2W,AA,TP,2.4X6.4MM 0.39OHM,5%,1/2W,AA,TP,2.4X6.4MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10ohm,5%,2W,AA,TP,4x12mm 22KOHM,5%,1/4W,AA,TP,2.4X6.4MM 1OHM,5%,1/2W,AA,TP,2.4X6.4MM Remarks ! ! ! ! ! ! ! ! ! ! ! ! 7-10 PN17LT/LO 7 Electrical Parts List Loc. No. R625 R630 R631 R632 R633 R641 R642 R660 R661 RB01 RB02 RB04 RB05 RB06 RB07 RB08 RB09 RG01 RG02 RG04 RG05 RG06 RG07 RG08 RG09 RR01 RR02 RR04 RR05 RR06 RR07 RR08 RR09 SK101 SK102 SK501 SKB01 SKG01 SKR01 TP501 X201 ZD101 ZD102 ZD103 ZD104 ZD201 ZD202 ZD203 ZD204 ZD205 ZD210 ZD211 ZD401 ZD601 ZD602 ZD603 ZD604 Code No. 2001-000515 2001-000786 2001-001088 2001-000290 2001-000211 2003-000744 2001-000290 2001-000290 2001-000527 2001-000969 2001-000666 2001-000003 2001-000645 2001-000449 2001-000705 2001-000025 2001-000290 2001-000969 2001-000666 2001-000003 2001-000645 2001-000449 2001-000705 2001-000025 2001-000290 2001-000969 2001-000666 2001-000003 2001-000645 2001-000449 2001-000705 2001-000025 2001-000290 1405-001064 4715-001055 4715-001055 4715-000102 4715-000102 4715-000102 6042-000002 2801-000005 0403-000509 0403-000007 0403-000007 0403-000007 0403-000355 0403-000355 0403-000355 0403-000355 0403-000361 0403-000361 0403-000337 0403-000355 0403-000361 0403-000509 0403-000361 0403-000361 Description R-CARBON R-CARBON R-CARBON(S) R-CARBON R-CARBON R-METAL OXIDE(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON SURGE ABSORBER SURGE ABSORBER SURGE ABSORBER SURGE ABSORBER SURGE ABSORBER SURGE ABSORBER EYELET CRYSTAL-UNIT DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER Specification 220OHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/2W,AA,TP,2.4X6.4MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1OHM,5%,1/4W,AA,TP,2.4X6.4MM 56ohm,5%,2W,AA,TP,4x12mm 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 22OHM,5%,1/8W,AA,TP,1.8X3.2MM 75OHM,5%,1/8W,AA,TP,1.8X3.2MM 33OHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,1/8W,AA,TP,1.8x3.2mm 330KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 39OHM,5%,1/2W,AA,TP,3.3X9MM 75OHM,5%,1/4W,AA,TP,2.4X6.4MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 75OHM,5%,1/8W,AA,TP,1.8X3.2MM 33OHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,1/8W,AA,TP,1.8x3.2mm 330KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 39OHM,5%,1/2W,AA,TP,3.3X9MM 75OHM,5%,1/4W,AA,TP,2.4X6.4MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 75OHM,5%,1/8W,AA,TP,1.8X3.2MM 33OHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,1/8W,AA,TP,1.8x3.2mm 330KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 39OHM,5%,1/2W,AA,TP,3.3X9MM 75OHM,5%,1/4W,AA,TP,2.4X6.4MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 400V,20%,-,-,AXIAL 1kV,+50-10%,-,-,RADIAL 1kV,+50-10%,-,-,RADIAL 200V,20%,1000A,-,RADIAL 200V,20%,1000A,-,RADIAL 200V,20%,1000A,-,RADIAL ID1.5,OD2,L3.1,SN,BSS3-E/EH 8MHz,50ppm,28-AAM,S,35ohm,TP MTZJ5.6B,5.6V,5.45-5.73V,500mW UZ6.2BSB,5.99-6.24V,500mW,DO-34,TP UZ6.2BSB,5.99-6.24V,500mW,DO-34,TP UZ6.2BSB,5.99-6.24V,500mW,DO-34,TP UZ5.1BSB,5.1V,4.97-5.18V,500mW UZ5.1BSB,5.1V,4.97-5.18V,500mW UZ5.1BSB,5.1V,4.97-5.18V,500mW UZ5.1BSB,5.1V,4.97-5.18V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ24BH,24V,24.2-25.7V,500mW,DO UZ5.1BSB,5.1V,4.97-5.18V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW MTZJ5.6B,5.6V,5.45-5.73V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW Remarks SNA SNA SNA SNA PN17LT/LO 7-11 7 Electrical Parts List Loc. No. HS301 CIS CIS CIS CIS HS601 CIS CIS CIS CIS HS103 CIS CIS CIS CIS HS402 CIS CIS HS401 HS403 CIS CIS CIS HS501 CIS CIS CIS CIS CIS CIS Code No. BH99-00002A 1204-001508 6006-001008 6021-000118 BH62-00003A BH99-00003A BH13-00004A BH61-00004A BH62-00004A BH62-20001B BH99-00004H 6006-001008 6021-000118 BH13-00020A BH62-00006A BH99-00005A BH61-00004A BH62-00008A BH99-00006A BH99-00006A 6006-001008 6021-000118 BH62-30024A BH99-00024F 0402-001413 0502-000465 0502-001129 BH61-00004A BH61-70003A BH62-00015A Description ASSY,HEAT/SINK IC-VERTICAL DEF. SCREW-ASS'Y MACH NUT-HEXAGON HEAT/SINK-V.IC ASSY,HEAT/SINK IC-HYBRID SPRING-TR HEAT/SINK-POWER RUBBER ASSY HEAT/SINK SCREW-ASS'Y MACH NUT-HEXAGON IC HYBRID HEAT SINK-VIDEO ASSY,HEAT/SINK SPRING-TR HEAT SINK-TR ASSY,HEAT/SINK ASSY,HEAT/SINK SCREW-ASS'Y MACH NUT-HEXAGON HEAT/SINK-TR ASSY HEAT/SINK DIODE-RECTIFIER TR-POWER TR-POWER SPRING-TR SPRING HEAT SINK-FBT Specification H/S V.IC,SCREW+NUT,KA2142,-,-,OIL SILICON,-,KA2142,SIP,10P,-,PLASTIC,35V,15W,-20TO+70C,ST,VERTICAL DEFLECTION WSP,BH,+,M3,L10,ZPC(YEL),SWRCH 1C,M3,ZPC(YEL),SM20C -,T1,-,A1050S,DA/DB H/S POWER,SPRING,DP104,-,-,RUBBER,-,-,DP104C,TO-220-5L,5P,POWER SWITCH,-,CDA,CDB,SUS304,T0.5,-,-,-,-,T1,-,A1050S,DA/DB CSQ4357,W25*L20*T0.45,-,-,-,HS VIDEO,SCREW+NUT,LM2467TA,-,-,OIL SILICON WSP,BH,+,M3,L10,ZPC(YEL),SWRCH 1C,M3,ZPC(YEL),SM20C LM2467T,PN15H/17L,9P,-20to+115C,TO-220-9L,10mA,85V,ST -,A1050S T2.0,-,DB H/S,SCREW+NUT,IRF630,-,-,OIL SILICON,-,CDA,CDB,SUS304,T0.5,-,-,-,-,SPC-1 L20*H45*T1,-,CDB H/S,SCREW+NUT,IRF630,-,-,OIL SILICON,-,H/S,SCREW+NUT,IRF630,-,-,OIL SILICON,-,WSP,BH,+,M3,L10,ZPC(YEL),SWRCH 1C,M3,ZPC(YEL),SM20C SPC,T1,SN,CFX1577L HS FBT,SPRING,KSC5802,DTV56F,KTD2058,OIL SILICON DTV56F,1500V,10A,TO-220,ST KTD2058,NPN,25000mW,TO-220IS,ST,100-200 KSC5802,NPN,70000mW,TO-3PF,ST,20-40 CDA,CDB,SUS304,T0.5,-,-,-,CVT4857,STS304-W1/2H,T0.5,W3.8 A1050S,T1.0,T1.0,-,- Remarks SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA 7-3 Others Loc. No. CRT ASSY PBA UNIT (17LT) (17LO) B/D ASSY CODE (17LT) (17LO) S/CABLE DEGAUSSING MAGNET Code No. BH03-00016A BH94-00207A BH94-00226A BH98-00191A BH98-00206A BH39-00282A BH27-00047A 3302-000006 Description & Specification M41QAR361X114(A/S2),69,17,0.28,-,29.1,FST,H/C,NH,-,MULTI,TILT,4 PN17LT-07C1/4243,-,-,PN17LO-07C1/9590,-,-,PN17LT-07C1/4243,-,-,PN17LO-07C1/9590,-,-,PN17LO,15P/06P.07P,20276,1500MM,UL20276,IVORY,D-SUB/MALE,-,-,320*250*1100mm,9.6mH,-,100Ts,ae10% AF,14G,1620-1980G,0.58-0.9MGOe Remarks SNA SNA SNA SNA SNA 7-12 PN17LT/LO PN17LT/LO SIGNAL VIDEO INPUT H/V SYNC UP, DOWN BRIGHTNISS CONTRASTER PIN, TRAP SIZE, POSI, DEGA. LED POWER MCU IC201 FRONT CONTROL BOARD EPROM IC202 24LC04 8 Block Diagrams VIDEO BOARD VIDEO PRE-AMP + OSD IC101 IC104 VIDEO OUTPUT IC103 RGB SOCKET RGB - CUTOFF IC102 G1 HEATER MAIN BOARD H-SYNC, V-SYNC H-SYNC1 V-SYNC1 E/W_OUT HOR./VER. PROCESSOR IC401 12C DATA 12C CLK TDA4859 KA2142 VER. OUTPUT IC301 HOR. DRIVE Q403 VER. DY CN401 F O C U S S C R E E N H/V H/V SIZE REG. FROM IC401 VERTICAL FOCUS B(+) HOR. DY CN401 FBT T501 -140V +30V H. D. T T401 HOR. OUT Q404 FROM MCU ACL CIRCUIT +12V REG. S-COR. DYNAMIC FOCUS T502 CONTRAST CONTROL CONTRAST CONTROL V-MUTE S-CORRECTION PS-2(POWER OFF) HOR. LINEARITY VER. BLANKING Q303 KSC945 G1 BRIGHTNESS CONTROL BRIGHTNESS CONTROL TILT +70V +50V TO VIDEO TO D-COIL ON THE CRT DEGAUSSING BLOCK RL601 POWER PWM CONTROL IC601C SWITCHING TRANS T601 -12V +13V VER. OUT 13V_1 VER.OUT & TILT / H_LIN. CONTROL -140V (FROM FBT) OFF MODE (FROM MCU) AC INPUT SOCKET CN601 LINE FILTER L601 BRIDGE RETIFIER Q610 +12V REGULATOR 12V +6.3V HEATER CRT HEATER 8-1 8 Block Diagrams Memo 8-2 PN17LT/LO 9 Wiring Diagram 4P DY 4P DY CN_DY CN603 CONTROL BOARD KEY-IN GND KEY-IN GND MPR II MPR II MPR II MPR II GND MPR II-wire NC PN17LT/LO 9-1 9 Wiring Diagrams Memo 9-2 PN17LT/LO 10 Schematic Diagrams 10-1 Main Part Schematic Diagram 9 23 3 12 18 4 11 10 14 13 8 7 6 12 5 PN17LT/LO 10-1 10 Schematic Diagrams 1 100 V (IC601, #1) 2 100V (IC601, #1) 3 2.00 V (IC401, #6) 4 1.00V (IC401, #8) 5 20.0 V (Q403, Collector) CH1 P-P = 100 V CH1 RMS = 350.2 V CH1 P-P = 100V CH1 RMS = 325.8 V CH1 P-P = 2.00V CH1 RMS = 5.868V CH1 P-P = 1.00V CH1 RMS = 1.298V CH1 P-P = 20.0 V CH1 RMS = 46.80V 6 200 V (Q408, Collector) 7 1.00 V (IC401, #11) 8 500 V (IC401, #12) 9 10.0 V (IC301, #6) 10 2.00 V (Q402, Gate) CH1 P-P = 200V CH1 RMS = 387.2V CH1 P-P = 1.00V CH1 RMS = 3.008 V CH1 P-P = 500 V CH1 RMS = 1.425 V CH1 P-P = 10.0 V CH1 RMS = 5.06 V CH1 P-P = 2.00 V CH1 RMS = 7.692V 11 50.0 V (Q402, Drain) 12 2.00 V (IC401, #32) 13 50.0 V (T502, #6) 14 100 V (T502, #1) 18 1.00 V (IC201, #13, 14) CH1 P-P = 50.0 V CH1 RMS = 73.7V CH1 P-P = 2.00V CH1 RMS = 6.124V CH1 P-P = 50.0V CH1 RMS = 75.6V CH1 P-P = 100V CH1 RMS = 124.0V CH1 P-P = 1.00 V CH1 RMS = 2.108V 23 5.00V (Q303, Collector) CH1 P-P = 5.00V CH1 RMS = 28.33V 10-2 PN17LT/LO 10 Schematic Diagrams 10-2 Video Part Schematic Diagram 24 19 20 22 16 21 15 17 PN17LT/LO 10-3 10 Schematic Diagrams 15 1.00V (IC101 #5, 6, 7) 16 1.00V (IC101 #18,19,20) 17 20.0V (IC103, #1, 2, 3) 19 1.00 V (IC104, #6) 20 1.00 V (IC104, #8) CH1 P-P = 1.00V CH1 RMS = 2.452V CH1 P-P = 1.00V CH1 RMS = 2.792V CH1 P-P = 20.0V CH1 RMS = 40.52V CH1 P-P = 1.00V CH1 RMS = 4.516V CH1 P-P = 1.00V CH1 RMS = 5.024V 21 1.00 V (IC101, #18,19,20) 22 10.0 V (R,G,B, Video) 24 20.00V (CRT Socket, G1) CH1 P-P = 1.00V CH1 RMS = 2.580V CH1 P-P = 10.0V CH1 RMS = 17.02V CH1 P-P = 20.0V CH1 RMS = 66.68V 10-4 PN17LT/LO |
Price & Availability of PN17LTLO
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |